English -1002 anonymous Installing Railings | Home Depot Canada
Home>Know-How Centre>Outdoors>Installing Railings
Projects

Installing Railings

Project Overview

Installing Railings

Building codes vary, but most require a railing on decks more than 30 inches above the ground. A railing height requirement of 36 inches is common. Railing posts can be attached to the outer face of the perimeter joists, or can be through posts supported by the footings. You can install railing in notched or unnotched posts, but notches are required if the decking overhangs the perimeter joists. Use any railing style that meets code. Spacing between balusters and between lower rails and decking can be no more than 4 inches in order to prohibit a child from getting though or stuck between the balusters. Plan spacing carefully if you choose balusters with decorative profiles because uneven surfaces may create larger spaces.

9 Steps

  1. MEASURE RAILING RUN
  2. MARK POST FOR STAIR STRINGER
  3. LAY OUT NOTCHES FOR RAILING
  4. LAY OUT NOTCH WHERE RAILS MEET
  5. ATTACH RAILS
  1. MITER RAIL ENDS
  2. ADD A HANDHOLD
  3. INSTALL STARTING POST
  4. CUT MITERS ON ENDS
Show all steps »
MEASURE RAILING RUN
MEASURE RAILING RUN

Step 1

MEASURE RAILING RUN

Measure the exact dimension of each railing run. A railing run is a straight section of railing uninterrupted by stairs or other changes in directin. Calculate the number and location of posts and the gap between balusters for each run. Plumb and attach each post wit h two carriage bolts or lag screws. Stagger the fasteners on both sides of the center of the post to prevent splitting. Cut notches in post before attaching, if necessary for the railing style. Make notches for rails the same depth as the notches on the rim joist. Fasten each rail to the posts. Drill pilot holes for fasteners at the ends of each rail to prevent splitting.

MARK POST FOR STAIR STRINGER
MARK POST FOR STAIR STRINGER

Step 2

MARK POST FOR STAIR STRINGER

Mark the slanted top shoulder of a notch for a post that will attach to a stair stringer. Plumb the post against the stringer at its correct height before marking. Cut the notch and install the post. Position one post at each end of a stair run. Install additional posts for long stair runs or to match the railing design. Mark the location for the upper edge of the top rail or for trimming the post top, depending on the railing style. Lay a long straight 2x4 across the stair treads. Measure to the railing height from the bottom edge of the 2x4 at each post to mark the top edge of a stair railing.

LAY OUT NOTCHES FOR RAILING
LAY OUT NOTCHES FOR RAILING

Step 3

LAY OUT NOTCHES FOR RAILING

Mark the notches for each stair rail in the posts. Hold or clamp the rails in positing against the post. Mark cutting lines on the end of the stair rail. End the rail in the center of the post if it meets a deck rail at the post. Also mark the stair rail notch location on the post.

LAY OUT NOTCH WHERE RAILS MEET
LAY OUT NOTCH WHERE RAILS MEET

Step 4

LAY OUT NOTCH WHERE RAILS MEET

Mark the notch location for a deck rail that meets a stair rail at a post. The top of a post where stair rail and deck rail meet will be level with other posts for deck railing. Cut the notch in the post. Remove as much of the notch as possible with a circular saw. Then finish removing waste material wit ha chisel. Mark the intersection angle between the stair rail and deck rail. Place the edge of the deck rail on the decking with one end protruding over the stairs. Lay the stair rail on edge on the treads to cross the deck tail. Mark both edges on both rails where they cross. Connect the marks across the face of each rail. Align a power mitersaw blade with a marked line and cut each rail to length.

ATTACH RAILS
ATTACH RAILS

Step 5

ATTACH RAILS

Attach the stair rails to the posts. Drill pilot holes at the ends of each rail to prevent splitting. Install each baluster with two fasteners at each end. Clamp several balusters to the rails at the spacing you used earlier-to make sure the spacing looks right. If it doesn’t, reclamp the balusters and recalculate their number. Cut a spacer long enough to span between rails and as wide as the gap between balusters. Check plumb every fourth baluster. Attach 2x6 cap rail across the tops of the posts and balusters. Join sections over a post and wit ha scarf join. Drive two fasteners into posts. Drive one fastener every 12-16 inches between posts into rail and balusters.

MITER RAIL ENDS
MITER RAIL ENDS

Step 6

MITER RAIL ENDS

Miter the ends of the cap rail and drive fasteners both through the corners and into the corner posts. Rough-cut a 2x6 a few inches longer than the finished length of the stair rail and hold or clamp it against the upper stair rail where it meets the post. Mark the bevel in the top end and cut it. Drive fasteners at an angle through the bevelled end of the cap rail and into the post. Drill pilot holes to prevent splitting.

ADD A HANDHOLD
ADD A HANDHOLD

Step 7

ADD A HANDHOLD

Attach a graspable handrail inside the stair railing, if necessary. Use brass, galvanized, or other rust-resistant hardware. Sand any sharp edges on the handrail. To fasten a handrail return, miter the ends of the handrail stock at 45 degrees. Test-fit the pieces before attaching them.

INSTALL STARTING POST
INSTALL STARTING POST

Step 8

INSTALL STARTING POST

Install a stair railing post at the top end of an angled stair stringer. Make a space between the post and the deck rail post no wider than the spacing between balusters. Also install the stair railing post at the bottom end of the stringer. Mark the angle for trimming each stair rail. Measure and mark locations for rail height. Temporarily position each stair rail board against the stair rail posts at the marks to mark the trimming line at each end of the board.

CUT MITERS ON ENDS
CUT MITERS ON ENDS

Step 9

CUT MITERS ON ENDS

Cut the miter at both ends of each stair rail. Install the stair rails, balusters, and cap rail following the methods just used.

Write a Review
QUICK RATE:

You have rated

 out of 5 stars.

Do you want to submit this quick rating?

Yes No

Thank you!
Your quick rate has been submitted.

Please note it may take up to 8 hours for your quick rating to appear.

Sorry we are currently experiencing technical difficulties. Please try and resubmit your Quick Rating.

Thank you, you have already quick rated this product.  out of 5

Project Details

Skill Level: Beginner

Time: 3 hours

Before you start, read this »

Due to differing conditions, tools, and individual skills, The Home Depot® assumes no responsibility for any damages, injuries suffered, or losses incurred as a result of attempting to replicate any of the home improvement ideas portrayed in this website Before beginning any home improvement project, review it thoroughly to ensure you or your contractor can finish the project and if any doubts or questions remain, consult local experts or authorities. Because codes and regulations vary greatly, you always should check with authorities to ensure that your project complies with all applicable local codes and regulations. Always read and observe all of the safety precautions provided by any tool or equipment manufacturer, and follow all accepted safety procedures.

Materials

Related Resources

Projects

    Buying Guides

    know how event34