Home>Know-How Centre>Outdoors>Laying Out Footings

Projects

Laying Out Footings

Project Overview

Laying Out Footings

Once the ledger is in place, you can use it to locate the footing, laying out the site and footing locations with batterboards and mason's lines. Mason's line can be stretched tightly without breaking and won't sag. Don't use a substitute. Batterboards must be rigid enough to stand straight against the tension of tightly pulled layout lines, so use stakes long enough to be driven securely into the ground.

6 Steps

  1. Mark the Post Center
  2. Put in Batterboards
  3. Stretch the Line
  4. Square the Corners
  5. Locate Corner Footings
  1. Mark Footing Centers
Show all steps »
Mark the Post Center
Mark the Post Center

Step 1

Mark the Post Center

Mark the center of the outside post location on the ledger. Partially drive a screw or nail at the bottom edge of the ledger at this mark to serve as a tie-off point for a plumb line. Drop a plumb line from the center mark. This transfers the point to the ground accurately.

Mark the Post Center
Mark the Post Center

Step 2

Put in Batterboards

Drive a batterboard near the wall at the bottom of the plumb line with the crosspiece level. If the ground slopes away from the house, install the crosspiece close to the ground so the batterboard at the opposite end will be no more than 3 feet high. Make a mark on the crosspiece aligned with the plumb line. Tie one end of the mason's line to a screw driver near the mark. Wrap the line several times around the crosspiece and line it up with the mark on the last wrap. Position the batterboard for the outside corner about 3 feet beyond the location of the footing.

Stretch the Line

Step 3

Stretch the Line

You can either preassemble the batterboard or drive the batterboard stakes and attach the crosspiece.. Attach the crosspiece with one screw if you haven't preassembled it. Wrap the line at the center of the crosspiece and stretch tight. Stretch the string until it is tight, level the line with a line level, and fasten the other end of the crosspiece with another screw. Install the remaining batterboards at the other corners.

Square the Corners
Square the Corners

Step 4

Square the Corners

Stretch the lines tightly, and adjust the batterboards until the lines just touch at their intersections. Square the corners using the 3-4-5 triangle method (see project tip). Once the corners are square, mark each crosspiece where the line crosses the top edge. This provides a reference point if the line gets moved inadvertently.

Locate Corner Footings
Locate Corner Footings

Step 5

Locate Corner Footings

Mark the center of the corner footings by dropping a plumb bob from a tripod (a camera tripod will do nicely) so the plumb line just touches the intersection of the layout lines. Insert a landscape spike where the plumb bob comes to rest. Tie colored tape or ribbon to the spike for visibility. Measure and mark the layout lines for the footing positions between the corners. Slip a small piece of tape over the line at the footing spacing.

Mark Footing Centers

Step 6

Mark Footing Centers

Drop a plumb line at each piece of tape. Drive a landscape spike where the plumb bob comes to rest. Tie a piece of colored tape or ribbon to each spike for visibility. If wind disturbs the plumb line, use a piece of plywood as a windscreen.

Write a Review
QUICK RATE:

You have rated

 out of 5 stars.

Do you want to submit this quick rating?

Yes No

Thank you!
Your quick rate has been submitted.

Please note it may take up to 8 hours for your quick rating to appear.

Sorry we are currently experiencing technical difficulties. Please try and resubmit your Quick Rating.

Thank you, you have already quick rated this product.  out of 5

Project Details

Skill Level: Intermediate

Time: 3 hours

Before you start, read this »

Due to differing conditions, tools, and individual skills, The Home Depot® assumes no responsibility for any damages, injuries suffered, or losses incurred as a result of attempting to replicate any of the home improvement ideas portrayed in this website Before beginning any home improvement project, review it thoroughly to ensure you or your contractor can finish the project and if any doubts or questions remain, consult local experts or authorities. Because codes and regulations vary greatly, you always should check with authorities to ensure that your project complies with all applicable local codes and regulations. Always read and observe all of the safety precautions provided by any tool or equipment manufacturer, and follow all accepted safety procedures.

Materials

  • Lumber
  • Screws
  • Landscape Spikes
  • Masking Tape
  • Colored Marking Tape

Tools

  • Tape Measure
  • Small Sledge
  • Line Level
  • Mason's String

Related Resources

Calculators and Tools

Projects

Buying Guides