English -1002 anonymous Wrapping Station | Home Depot Canada
Projects

Wrapping Station

Project Overview

Wrapping Station

This compact-sized, wall-mounted wrapping station keeps all of your ribbons, paper and accessories neatly organized. Build two identical pieces, one for paper and one for ribbons. Once installed, you can quickly access supplies whenever a birthday or holiday event occurs.

8 Steps

  1. Cut supports
  2. Cut supports to length
  3. Cut end pieces
  4. Drill holes for dowels
  5. Cut notches for ribbon/paper dowel carrier
  1. Assemble
  2. Finishing
  3. Install
Show all steps »
Cut supports

Step 1

Cut supports

Using a table saw with the blade set at 45º and an 8' piece of 1" x 4" select pine, make a rip at 2-1/2". Save the 1-1/8" offcut for the second support. From another 1" x 4" piece of select pine, make a 45° rip at 1-1/2" to create the hanger bracket.

Cut supports to length

Step 2

Cut supports to length

Using the mitre saw, cut the supports to 34-1/2". Cut the 1-1/2" support bracket slightly shorter, to 34-3/8".

Cut end pieces

Step 3

Cut end pieces

From a 4 ft. length of 1" x 6" clear pine, cut 4 square end pieces, 5-1/2" x 5-1/2". Then measure 1" off 2 opposing corners and cut off at a 45º angle. This will create triangular pieces with 2 right-angled corners.

Drill holes for dowels

Step 4

Drill holes for dowels

Align and clamp end pieces together and drill a 1/2" hole in one of the offset corners to accept the 1/2" dowel that will act as a straight edge.

Cut notches for ribbon/paper dowel carrier

Step 5

Cut notches for ribbon/paper dowel carrier

Using a trim router and a 1/4" double-fluted bit, rout a channel 3/8" deep on an angle, and 7/16" wide, to accept the dowel that will hold ribbon/paper.

Assemble

Step 6

Assemble

Assemble unit by gluing bottom and rear supports flush to the back of the end pieces – the 45° angles should be oriented as shown in figure 6. During assembly, also glue a 1/2" dowel, cut to 35" long, into the predrilled holes. Countersink 1-1/4" #8 woodscrews – 2 in the ends of the rear support and one at each end of the bottom support. Glue 3/8" and 1/2" birch mushroom caps to hide the screws and dowel hole. Following assembly, cut the second dowel to length to fit between the routed channels – this is the removable carrier for ribbons or paper.

Finishing

Step 7

Finishing

Fill, sand, prime and paint as desired.

Install

Step 8

Install

Using 2" woodscrews and drywall plugs, install the wall mounting bracket on the wall with the 45º angle facing in to accept the 45º angle on the back support piece.

Write a Review
QUICK RATE:

You have rated

 out of 5 stars.

Do you want to submit this quick rating?

Yes No

Thank you!
Your quick rate has been submitted.

Please note it may take up to 8 hours for your quick rating to appear.

Sorry we are currently experiencing technical difficulties. Please try and resubmit your Quick Rating.

Thank you, you have already quick rated this product.  out of 5

Project Details

Skill Level: Beginner

Time: 4 hours

Before you start, read this »

Due to differing conditions, tools, and individual skills, The Home Depot® assumes no responsibility for any damages, injuries suffered, or losses incurred as a result of attempting to replicate any of the home improvement ideas portrayed in this website Before beginning any home improvement project, review it thoroughly to ensure you or your contractor can finish the project and if any doubts or questions remain, consult local experts or authorities. Because codes and regulations vary greatly, you always should check with authorities to ensure that your project complies with all applicable local codes and regulations. Always read and observe all of the safety precautions provided by any tool or equipment manufacturer, and follow all accepted safety procedures.

Materials

  • (12) 1-1/2" And (4) 2" Wood Screws, Drywall Plugs
  • Sandpaper – 120 And 220 Grit (1 Sheet Each)
  • 941 mL Paint, If Desired
  • 3/8" x 36" Dowel – 2 Pieces
  • 1" x 4" Select Pine – 3 Pieces, 8 Feet
  • 1" x 6" Select Pine – 1 Piece, 8 Feet
  • 400 mL Carpenter's Glue
know how event34