BUY ONLINE PICK UP IN-STORE Available for in-store products Learn More ›

Build a Vertical Garden Wall

Think up with a living garden wall.

Urban-minded and space-limited green thumbs will also love this garden's low-maintenance style.

SEE ALL THE STEPS

  •  There are 12 steps to completing this project:
    Step 1  CUT
    Step 2  ROUND OVER BOARD EDGES
    Step 3  ASSEMBLE THE BOX
    Step 4  DIVIDE BOX INTO SECTIONS
    Step 5  PREPARE BOX FOR BACK INSERTION
    Step 6  INSERT THE BACK
    Step 7  ADD SOIL
    Step 8  CUT COCO MAT
    Step 9  AFFIX COCO MAT
    Step 10  ATTACH FRAME
    Step 11  PLANTING
    Step 12  HANG THE BOX
MATERIALS YOU WILL NEED

  • (4) 1 x 6 x 6' Cedar Fence Boards
    6 Pieces Tongue-and-groove Cedar Beadboard V-Match Panelling, 5/16" x 1-9/16" x 8'
    (6) 24" x 24" Patio Life Replacement Coconut Planter Lining
    1 Large Bag Potting Soil
    Small Box 1-1/4" Brad Nails
    Small Box 1-3/4" #8 Deck Screws
    Small package T50 1/2" staples
TOOLS YOU WILL NEED

  • Table Saw
    Drill Gun
    Countersink Bit
    Mitre Saw
    Trim Router
    1/4" x 1/4" Roundover Bit
    Brad Nailer
    Compressor
    Utility Knife
    T-50 Staple Gun
    Tape Measure
    Red Sharpie Marker
    Pencil

1  CUT


From 4 pieces 1 x 6 x 6' cedar fence boards rip:

1)  2 at 3-1/4"
2)  2 at 3"
3)  2 at 1-1/4"
4)  2 at 3/4"


2  ROUND OVER BOARD EDGES


Using a router and 1/4" shank, 1/4" round-over bit, round-over the ripped edge of the 1-1/4" strips to match the round over of the finished edge. This will be the material for the frame.


3  ASSEMBLE THE BOX


Cut the 3-1/4" material to size. Our box is 41" x 14-1/2" outside measurement. Hold the box together with 1-1/4" brad nails. Then countersink and screw the box together with 8 x 2" #2 deck screws. Use the 3" strip to divide the box lengthwise. Countersink and screw together. Make the 3" pieces flush with the front.


4  DIVIDE BOX INTO SECTIONS


Our box has 3 framed sections that are divided into 4 smaller sections (making 12 smaller squares). Each of the dividers is offset to allow for nailing. To make this easy, make 2 spacers (12-5/8" and 5-3/4"). Be sure that the dividers are flush with the front of the box when nailed in place. Start at one end using the 12-5/8" spacer and nail in 2 dividers. Then turn the box around and starting at the other side (to create the offset) nail in 2 dividers. Using the 5-3/4" spacer, insert the rest of dividers, coming off of the dividers that we already inserted. From the outer edge of the box, countersink and screw each divider.


5  PREPARE BOX FOR BACK INSERTION


There will be a 1/4" inset on the back side of the box. This will be where the back will be fitted. In this step use the 3/4" strip, cut and fit it to go around the inside of the outer edge. Make sure that it is flush with the 3" dividers and the middle, keeping the space where the back will sit. This will be a nailing strip.


6  INSERT THE BACK


Cut the cedar beadboard panelling to fit in the back grove. Pin-nail into the strips and middle.


7  ADD SOIL


Fill each of the sections with soil.


8  CUT COCO MAT


Cut the coco mat so that it will fit flush on the front edge. Cut it so that it will go through the middle of the offset dividers that you first put in.

It will take three sections of the coco mat to cover the front.


9  AFFIX COCO MAT


Staple the mat to the box. The seam will be covered by the frame. Be sure to staple through the dividers and the middle so that each section is firm.


10  ATTACH FRAME


Cut the 1-1/4" frame material to fit flush to the outside of the box and nail through the coco mat into the front edge of the box.

Then measure and cut the two divider pieces and brad nail in place, making sure to cover seams.


11  PLANTING


We planted several varieties of succulents that are ideal for this type of garden.

Using a utility knife, cut a semi-circle in each of the 4 sections. This will create a pocket in each section.

Then pull the mat back and insert the plant. Pack with soil.


12  HANG THE BOX


Use hanger clips on the back to hang the box on an outer wall or fence.


What You Need for This Project