L'événement Stanley Days est en cours. N'attendez pas !  Magasiner l'événement.
Choisissez vos options

Aperçu

Modèle # 2505-20 Internet # 1001501060

Le MILWAUKEE® M12 FUEL Perceuse-visseuse d'installation dispose de 4 solutions dédiées, offrant un accès et un contrôle inégalés avec jusqu'à 300 pouces-lbs. de couple maximum. Quatre têtes dédiées, incluant un mandrin de 3/8 de pouce, un tournevis excentré, un tournevis hexagonal ¼-Inch et un tournevis à angle droit, peuvent être fixées dans 16 positions différentes. Les utilisateurs disposent ainsi d'une solution de perçage et d'enfoncement 4 en 1 conçue spécialement pour atteindre les endroits difficiles. La perceuse/visseuse modulaire est équipée d'un moteur Brushless POWERSTATE, offrant aux utilisateurs 1600 RPMS et 300-Inch/lbs de couple. Ils disposent ainsi de la puissance nécessaire pour les applications d'installation, en particulier dans les domaines de l'électricité, de l'installation d'armoires, du MRO, du HVAC, de l'automobile et de la rénovation. La perceuse/visseuse compacte sans fil est alimentée par la batterie de Milwaukee M12 REDLITHIUM REDLITHIUM (non incluse), offrant aux utilisateurs plus de temps de fonctionnement par charge et plus de travail pendant toute la durée de vie de la batterie.

  1. Le moteur POWERSTATE Brushless fournit 300 lb-pi de couple maxi.
  1. Clip de ceinture attaché
  1. Compatible avec toutes les batteries M12 (vendues séparément)
  1. Le sac compartimenté de l'entrepreneur facilite l'organisation de l'attache et la mobilité des outils.
  1. Le porte-embouts magnétique retient plusieurs embouts sur la carte pour gagner du temps lors du changement d'accessoires.
  1. La poignée en ligne permet un contrôle maximal de l'outil et un accès plus facile aux endroits difficiles d'accès.
  1. Le dessus de l'outil est plat, ce qui facilite le perçage et la fixation lorsque l'outil est au ras d'une surface.
  1. Inclut : Perceuse-visseuse d'installation (2505-20), 4 solutions dédiées (mandrin de 3/8 de pouce, tournevis hexagonal de ¼ pouces, décalé et à angle droit)
  1. La fixation décalée permet un accès optimal aux coins étroits et n'endommagera ni ne marquera les matériaux finis lors de la fixation.
  1. La fixation à angle droit permet une fixation et/ou un perçage efficace à 90° pour un accès inégalé dans les espaces restreints.
  1. Les mandrins à six pans de 3/8 po et les attaches décalées se connectent à l'attachement à angle droit pour plus de polyvalence lors du perçage et de la fixation à angle droit.
  1. Les accessoires se connectent dans 16 positions différentes pour un accès sous presque tous les angles.
  1. Inclut : Clip de ceinture et sac d'entrepreneur compartimenté

Spécifications


Sans fil/avec fil

Sans fil


Tension (en volts)

12


Vitesse variable

Oui


Caractéristiques de l'outil à moteur

Lumière à DEL, Boîtier inclus


Type de mandrin

Hex


Nombre de piles comprises

0

Dimensions

Hauteur assemblé (en pouces)
9.69
Hauteur de l’emballage (en pouces)
9.69
Largeur assemblée (en pouces)
14.96
Largeur de l’emballage (en pouces)
14.96
Poids assemblé (en livres)
5.39
Poids de l’emballage (en livres)
5.39
Profondeur assemblé (en pouces)
4.21
Profondeur de l’emballage (en pouces)
4.21

Détails

Batterie et chargeur
Outil seulement
Caractéristiques de l'outil à moteur
Lumière à DEL, Boîtier inclus
De batterie inclus
Non
Guide de coupe au laser
Non
Moteur
Moteur sans balais
Nombre de piles comprises
0
Nombre de vitesse
2
Nombre doutils inclus
5
Pays d'origine
US-United States
Portatif ou fixe
Portatif
Sans fil/avec fil
Sans fil
Taille du mandrin (en po)
3/8 po.
Tension (en volts)
12
Type d'outil à moteur
Perceuses-visseuses
Type de mandrin
Hex
Type de pile, de batterie ou dalimentation
Lithium-ion
Vitesse Maximum (tr/min)
1600
Vitesse variable

Garanties et certifications

Garantie limitée de 5 ans. Pour de plus amples informations, veuillez appeler le 1-877-948-2360.
M12 FUEL 12V Li-Ion Brushless 4-in-1 Installation 3/8-inch Drill Driver W/ 4 Tool Head (Tool Only)Milwaukee Tool M12 FUEL 12V Li-Ion Brushless 4-in-1 Installation 3/8-inch Drill Driver W/ 4 Tool Head (Tool Only)Le MILWAUKEE® M12 FUEL Perceuse-visseuse d'installation dispose de 4 solutions dédiées, offrant un accès et un contrôle inégalés avec jusqu'à 300 pouces-lbs. de couple maximum. Quatre têtes dédiées, incluant un mandrin de 3/8 de pouce, un tournevis excentré, un tournevis hexagonal ¼-Inch et un tournevis à angle droit, peuvent être fixées dans 16 positions différentes. Les utilisateurs disposent ainsi d'une solution de perçage et d'enfoncement 4 en 1 conçue spécialement pour atteindre les endroits difficiles. La perceuse/visseuse modulaire est équipée d'un moteur Brushless POWERSTATE, offrant aux utilisateurs 1600 RPMS et 300-Inch/lbs de couple. Ils disposent ainsi de la puissance nécessaire pour les applications d'installation, en particulier dans les domaines de l'électricité, de l'installation d'armoires, du MRO, du HVAC, de l'automobile et de la rénovation. La perceuse/visseuse compacte sans fil est alimentée par la batterie de Milwaukee M12 REDLITHIUM REDLITHIUM (non incluse), offrant aux utilisateurs plus de temps de fonctionnement par charge et plus de travail pendant toute la durée de vie de la batterie.
Milwaukee Tool
1001501060
CAD2292024-02-23
Home Depot Canada
M12 FUEL 12V Li-Ion Brushless 4-in-1 Installation 3/8-inch Drill Driver W/ 4 Tool Head (Tool Only) est évalué 4.7 de 5 de 1207.
  • y_2024, m_2, d_23, h_7
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.38
  • cp_1, bvpage1
  • co_hasreviews, tv_35, tr_1172
  • loc_fr_CA, sid_1001501060, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 74ms
  • REVIEWS, PRODUCT
Rated 4 de 5 de par Great tool with one aggravating issue This is a great and versatile tool. I have shied away from multi-tools like this in the past because usually it's never very good at anything, just mediocre at best. This tool is very good and plenty powerful for it's intended purpose. The glaring issue I have found is that the offset drill head uses a magnet to hold the drill/driver and not a ball bearing collar. This means the drill leaves the bit in the wood as I'm pulling it back out. Also, I've had the driver bit get pulled out of the attachment after driving in a screw. Not fun when you're up on a ladder and dropping items on finish pieces or co-workers. I'd like to see this attachment updated and an option for us Gen 1 owners to swap out for the fixed version.
Date de publication: 2020-03-23
Rated 3 de 5 de par Still haven’t made up my mind It is incredibly handy, swapping from 90 to drill chuck to hex chuck. However there needs to be an extension to push the 90 farther from the tool. It is just too close. My big concern/complaint, the teeth that lock the chucks from spinning to the tool slip. I have had it do this multiple times, especially when using the 90. It jumps and I have to stop what I’m doing to readjust the angle. Anytime there is slipping like this you have to be concerned with teeth rounding off. How long are they going to last. I was shocked by the torque this little tool has. I was able to drill through double top plates and joist. I just don’t know if it was a good buy yet....
Date de publication: 2019-12-22
Rated 4 de 5 de par Very close to a great tool But needs a couple of very minor things changed to make it a great tool. First, replace the electronic button for forward and reverse with a traditional thumb slide switch like every other drill / driver has. And second, make the hand-guard removable, so it can be there as a hand grip when you need it, but, when you need to get into tight places, it can be removed. These 2 things bring this tool down to a lower level then it actually is. From a functional standpoint it is great, does everything as it should, but with 2 minor changes it could be the best tool of its type.
Date de publication: 2019-11-23
Rated 5 de 5 de par Great little tool Only had this tool for a little while so here's what we did: Bored holes in a slab for door knobs using 2-1/8" & 1" hole saws with 3/8" chuck attachment. (Powered through in low speed High speed was a little sheepish) Drove 2-1/2" wood screws in 2x4"s using 1/4" Hex head attachment. Cut 1-1/4" holes in 3/8" porcelain tile using 3/8" chuck. Loved the magnetic tray. Holds bits & screws well. I can say that the offset head attachment will not made it easier to install standard doorknobs as it is too big for the bit to align straight with the screw. Nevertheless I am happy with this as an upgrade from my 2402 M12 Fuel Hex Screwdriver. I think I'll get the 48-32-4507 bit set to compliment it.
Date de publication: 2019-12-14
Rated 4 de 5 de par Tight space and general screw shootin' wizard If you could only have one drill / driver, there are compelling arguments to be made that it should be one of these. It's small enough to do your screwin' and drillin' in tight spots; you just can't believe it. The various attachments let you get into awkward positions you never thought possible, while the built in LED light will illuminate your way to just the right spot, in the early morning or in the middle of the night! The mechanical clutch prevents her from losing grip at a critical moment--and the light weight will never be a burden, even during your most arduous screw-sessions. She has the power and the stamina to keep on going all day.
Date de publication: 2022-09-01
Rated 5 de 5 de par A great too for general use. It's a great smaller tool for general purpose plus tight spots and right angle needs. It has become my go to tool over my larger drivers since it has enough power for all but the toughest jobs. It's also good for more sensitive applications where precise control is important or too much power may break something you don't want to. The torque adjustment helps keep from breaking things, too. Battery life is excellent and changing the heads is quick and easy. If I had bought this first I probably wouldn't own at least on of my other drivers. Think about making this the first driver you buy and it may be the only one you find you need.
Date de publication: 2022-07-28
Rated 5 de 5 de par M-12 Installation Drill I have no regrets purchasing the M12 Installation Drill. I have used two of the four attachments so far for installing my hardwood flooring. The drill is more than powerful to drive 3-inch screws. I was hesitant to buy this unit because many reviewers spoke negatively about the controls being on top of the drill. I have found this placement as an advantage because I don’t inadvertently hit the forward/reverse switch during use of this drill. Hitting the forward/reverse switch on my M-12 surge impact driver has been a issue for me occasionally. In summary, this is a great drill with many application via the four attachments. I recommend this drill.
Date de publication: 2022-11-06
Rated 4 de 5 de par Awesome in many ways, needs a few tweaks. Torque management needs a little more finesse. I love the attachments and flexibility of this tool but the clutch settings on such a specialized tool should be adjustable down to very VERY LOW twist. I have a vintage Porter Cable with adjustable clutch that can go so "soft" I can stop the bit with a pinch from two fingers. On a close-quarters/assembly tool, that is a feature I feel is "required". The knuckle guard thingy is also a bit of a hinderance for tight spaces. While assembling a small item I found I just couldn't position the driver where I needed it due to that extra piece. Not the fault of the tool, but an interesting choice for tight spaces.
Date de publication: 2022-06-13
  • y_2024, m_2, d_23, h_7
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.38
  • cp_1, bvpage1
  • co_hasreviews, tv_35, tr_1172
  • loc_fr_CA, sid_1001501060, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 24ms
  • REVIEWS, PRODUCT

Anyone else have issues with the clutch? There's very little difference between lowest and highest settings -- all very weak. I need to put into drill mode for it to even seat a drywall screw. Not sure if I have a dud or if it's normal for the 2505?

Posée par: Mike
I would say that you have a faulty drill. I have never had any problem. I have driven 3" screws into wood many times with no problem
Répondue par: Jones
Date de publication: 2023-05-07

Is the bag included?

Posée par: Wildbill
Yes, the bag is included. It is the same bag that comes with the full kit so it has hook and loop for the charger as well as everything included with this kit.
Répondue par: WolverineWoodworker
Date de publication: 2023-05-06

Does this have a light?

Does this have a light?
Posée par: Bob
Yes, it has a work area LED light.
Répondue par: MilwaukeeElectric
Date de publication: 2023-05-06

I?m looking for just a charger for cordless drill

Posée par: Milwaukee
Works with Milwaukee's standard 12 volt charger that should be readily available.
Répondue par: mdlatch
Date de publication: 2023-12-27

Will the xc6.0 battery fit this?

Posée par: AnchoVez
Yes, M12 RedLithium batteries XC4.0 and XC 6.0, good work efficiency.
Répondue par: Mario
Date de publication: 2023-05-06

Will this drill through 2x4 studs to run wiring (cables, romex, etc.)?

Will this drill through 2x4 studs to run wiring (cables, romex, etc.)?
Posée par: DIYer
Yes. But I wouldn't go over a 1 inch wood blade bit size. Need to use the Milwaukee HAWG for bigger holes/drill bits.
Répondue par: MattB
Date de publication: 2023-05-07

OK out of stock when will this be in stock seems like it was never really released?

OK out of stock when will this be in stock seems like it was never really released?
Posée par: jaded
Im sure they are waiting on FedEx because FedEx sucks
Répondue par: NICK
Date de publication: 2021-07-18

Will this be available before Christmas?

Will this be available before Christmas?
Posée par: Bob
Awesome little tool!
Répondue par: Tyler
Date de publication: 2023-05-07
  • y_2024, m_2, d_23, h_7CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.38
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_15
  • loc_fr_CA, sid_1001501060, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 77ms
  • QUESTIONS, PRODUCT