Le Vendredi fou du printemps des Pros est en cours. N’attendez pas!  Magasinez maintenant

Aperçu

Modèle # 3691 Internet # 1001043541

Protégez votre maison contre les dommages causés par l'eau grâce aux produits de gouttière, soffite et fascia en aluminium de Peak. Faits d'aluminium robuste, nos produits sont attrayants, fiables et ne nécessitent aucun entretien. Ils ne rouillent et ne fuient pas, ce qui est idéal pour conserver la beauté de votre demeure pendant des années. Nos produits sont robustes et attrayants, mais qu'est-ce qui les rend si exceptionnels? Tous les composants sont revêtus d'une peinture polyester extérieure, à l'intérieur comme à l'extérieur, pour vous procurer un produit durable, qui a une belle apparence de n'importe quel angle. De plus, nos étriers de gouttière sont conçus pour en faciliter l'installation en toute sécurité et d'une seule main! Utilisez la sangle de tuyau de descente en aluminium de 13 1/2 po pour fixer solidement les tuyaux de descente de 3 po x 3 po à votre mur.

  1. Idéal pour fixer solidement au mur les tuyaux de descente pluviale de 3 po x 3 po
  1. Fait d'aluminium robuste pour plus de résistance et durabilité
  1. Fini avec de la peinture polyester des deux côtés du tuyau de descente
  1. Facile à nettoyer, beauté sans aucun entretien pour ajouter de la valeur à votre maison
  1. Plus écologique que d'autres produits en PVC
  1. Disponible en stock dans certains magasins dans l'Est et l'Ouest du Canada
  1. Installez le protège-gouttière Peak en aluminium pour empêcher les feuilles, les débris et les aiguilles de pin de boucher votre système de gouttière
  1. Fabrique au Canada

Spécifications

Dimensions

Hauteur assemblé (en pouces)
0.054
Hauteur de l’emballage (en pouces)
0.05
Largeur assemblée (en pouces)
2
Largeur de l’emballage (en pouces)
2
Poids assemblé (en livres)
0.03
Poids de l’emballage (en livres)
0.03
Profondeur assemblé (en pouces)
12.5
Profondeur de l’emballage (en pouces)
12.5

Détails

Pays d'origine
CA-Canada

Garanties et certifications

Pour plus d'informations, veullez contacter le Service à la clientèle de Peak Products à 1-877-883-7325
Sangle de tuyau de descente en aluminium de 13 1/2 pouces en marron - Convient aux tuyaux de descente de 3 pouces x 3 poucesPeak Sangle de tuyau de descente en aluminium de 13 1/2 pouces en marron - Convient aux tuyaux de descente de 3 pouces x 3 poucesProtégez votre maison contre les dommages causés par l'eau grâce aux produits de gouttière, soffite et fascia en aluminium de Peak. Faits d'aluminium robuste, nos produits sont attrayants, fiables et ne nécessitent aucun entretien. Ils ne rouillent et ne fuient pas, ce qui est idéal pour conserver la beauté de votre demeure pendant des années. Nos produits sont robustes et attrayants, mais qu'est-ce qui les rend si exceptionnels? Tous les composants sont revêtus d'une peinture polyester extérieure, à l'intérieur comme à l'extérieur, pour vous procurer un produit durable, qui a une belle apparence de n'importe quel angle. De plus, nos étriers de gouttière sont conçus pour en faciliter l'installation en toute sécurité et d'une seule main! Utilisez la sangle de tuyau de descente en aluminium de 13 1/2 po pour fixer solidement les tuyaux de descente de 3 po x 3 po à votre mur.
Peak
1001043541
CAD2.842024-04-23
Home Depot Canada
Sangle de tuyau de descente en aluminium de 13 1/2 pouces en marron - Convient aux tuyaux de descente de 3 pouces x 3 pouces est évalué 4.5 de 5 de 363.
  • y_2024, m_4, d_23, h_5
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.41
  • cp_1, bvpage1
  • co_hasreviews, tv_254, tr_109
  • loc_fr_CA, sid_1001043541, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 80ms
  • REVIEWS, PRODUCT
Rated 3 de 5 de par Leaves & Debris ON gutter rather than IN gutter. I installed this kit around the back of my house where we have heavy leaf and tree debris. Usually, it takes a good hour of power washing to clean out my gutters each fall. This kit reduced my cleaning time down to about 10 minutes using only a leaf blower. Don't be misled – debris will still pile up on the gutter guard due to its design, just not *in* the gutter. I would have preferred a completely flat-surfaced design so the debris just blows off, but this kit was the only thing that fit my particular eaves roughing. To be fair, the retaining lip in the design that prevents debris from just blowing away, also prevents rain from washing right off the edge of the house.
Date de publication: 2021-11-19
Rated 4 de 5 de par Did the trick I bought four of these as my house has a flat roof and the drains had no strainers of any kind. Most of the trees in my area have small leaves so I was concerned that the gap between the grating was too big. To supplement these I bought a small amount of screen door mesh and wrapped a piece around each strainer and then installed the ring. This worked great and allows water to still drain but nothing else to enter the drain. The included rings were slightly larger than my drains so because they are thin gauge aluminum I simply used a pair of scissor to make a cut from top to bottom. When I installed the rings into the drain the diameter could now be reduced and the ends just overlapped each other slightly.
Date de publication: 2017-04-07
Rated 4 de 5 de par Nice gutter but use rivets! I followed Peaks instructions and ended up with a leaky gutter! The sections fit together poorly and when the joint hanger was screwed in gaps formed between the sections at the lap joints causing the thin layer of caulking to pull apart. I ended up assembling the entire gutter length (36') on the ground by caulking and clapping each lap joint and adding two aluminum rivets to the back (This Old House tip!) and one to the front near the top. I allowed 24 hours for the caulking to completely cure before moving the gutter.
Date de publication: 2016-09-15
Rated 5 de 5 de par Peak Products 5" Aluminum Gutter Guard An incredibly ingenious design! An absolute snap to install especially for someone like me who is spatially challenged. The 4 ft. length makes it easy to handle - especially when you're up on a ladder or on the roof. Every length is a perfect fit and attached with only 3 self tapping metal screws. The Peak "Gutter Guard" is, in my opinion, the best gutter guard on the market. Superb construction, well priced and after 4 months of heavy rains, they work flawlessly.
Date de publication: 2013-03-04
Rated 5 de 5 de par Great product but use some Philips screws Great product, better fit than the MHomes product. But I recommend you buy some SS Robertson pan heads so you can install one handed with the cordless drill. Phillips screws are a poor choice. But the actual gutter guard is great, good end to end recessed nested fit. Appreciated the pre-etched cardboard corner template. I would use again and recommend. I await to see how they do in winter and big storm events. But this locatoin is too high to clean from a ladder. I was able to install from the roof (using safety equipment)
Date de publication: 2013-10-08
Rated 3 de 5 de par Ambivalent I decided to wait for a few months after installing before I commented. As previously mentioned by others, easy to install, fit into gutters nice and snugly, Canadian made, decent price point and really do work at keeping eaves troughs from plugging up. Unfortunately guards are stamped in such a way that when installed there is a sheltered 3/8 inch deep by approximately 2 1/2 inch wide "dead zone" the entire length of the trough. Pine needles in particular accumulate (pile?) in this dead zone restricting water from entering the gutter trough. So far I've taken the leaf blower out once a month to blow off the pine needles. If the top of the gutter guard were not "a dead zone" but were flat or convex, the prevailing breeze may have been able to blow some of the deterius away instead of me pulling out the leaf blower. I expected more from the product and wish I had researched other alternatives a little more thoroughly.
Date de publication: 2019-08-14
Rated 5 de 5 de par Almost perfect Likes: Snaps into eavestrough until you can screw it down. Nests either over or under a drip edge, depending on where you are in the slope of the run. Holes small enough to keep out pine needles. No need to screw to (and compromise) fascia. Sloped side directs water away from fascia, preventing wood rot. Suggestions: It's easier to miter at corners if you follow the holes as shown in the template picture printed inside the carton. I'm surprised that the manufacturer doesn't prepunch 3 - 6 screw holes along the outer edge of each piece. Each piece looks to be punched before forming it. This would help guide the screw to the trough. Instead of phillips screws, buy a package of ¼" hex head self tapping screws and a magnetic driver bit. That's what the pros use, for ease, speed and safety. Use stainless steel Robertson® metal screws if rust is a concern.
Date de publication: 2018-11-09
Rated 4 de 5 de par Good product After struggling with the first section, I opted to pre-drill the flange for screw holes as I found without that, the screws skidded on the shiny surface. I also used Robertson screws, but then, that's what Canadians do!
Date de publication: 2016-09-16
  • y_2024, m_4, d_23, h_5
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.41
  • cp_1, bvpage1
  • co_hasreviews, tv_254, tr_109
  • loc_fr_CA, sid_1001043541, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 48ms
  • REVIEWS, PRODUCT

Hi. I have a 42 foot length of gutter. If this fits under drip edge would the last half of the run be at a pretty severe slope and just drain the water over the side with a heavy downpour?

Posée par: Robin
Hi, Thank you for your question, The vendor have confirmed that the gutter guards are compatible with a roof that has an installed drip edge. The guards will not impede the flow or drainage of your gutters. Vendor have requested to get in touch with them at 1-877-883-7325 or by e-mail at cservice@peakproducts.com for further assistance.
Répondue par: The Home Depot Canada
Date de publication: 2023-11-08

Wouldn't leaves, dirt, moss, pine needles, branch debris etc. accumulate on top this mesh which would block many of the holes in the mesh causing rainwater overflow during heavy rain ?

Posée par: cantrin
Any debris that sits on the top of the mesh just blows off, does not ever block the holes. Never over flows, I have them on my house and my cottage.
Répondue par: Jen L
Date de publication: 2021-10-03

How do you install the gutter guard with a metal roof? Can you post the installation manual?

Posée par: pinky
These gutter guards are installed on your gutters (which channel water to the down-pipes). Your metal roof channels the water to your gutters. These gutter guards are excellent in keeping leaves from entering the gutters and the down-pipes.
Répondue par: Anthony63
Date de publication: 2020-06-03

Hi, I have an old gutter system which using nails. Some of the nails are broken so I need to replace them. Will this gutter hanger work for the old gutter system? Thanks.

Posée par: Jack
These are the best gutter hangers I have used, mine for the the 5" gutter. They are slices of extruded aluminum with an aluminum screw to anchor well into a thick facer board and/or rafter end. Much better than nails. It securely holds the back wall of the gutter, and the front end hooks under the lip of many gutter profiles. You would need to try a sample hanger inside of your gutter profile to confirm the fit. I have these installed for only one winter, with perforated aluminum leaf covers, and the gutters have all held up a full load of ice buildup. One bracket did split due to the ice expansion, and I have simply replaced it.
Répondue par: Homeowner
Date de publication: 2020-05-27

Since these lay flat in the gutter creating a mini trough, it looks like debris will sit there eventually preventing water from getting in the gutter.  Other brands, like Easyon have a slope that looks like debris might slide off. Do either ot these clog?

Posée par: Roter
Peak Products Gutter Guard are made from heavy duty aluminum which even allowed me to rest a step ladder against the eavestrough and no damage was caused.  I have no issues with the mini trough you have mentioned and this helps prevent excessive rainfall from flowing over the eaves. 
Répondue par: Brad
Date de publication: 2020-09-25

Will this product work if the roof has drip edge installed?

Posée par: Martin
Hi, Thank you for your question, The vendor have confirmed that Yes, gutter guard will work on a roof with an installed drip edge. Vendor have requested to get in touch with them at 1-877-883-7325 or by e-mail at cservice@peakproducts.com for further assistance.
Répondue par: The Home Depot Canada
Date de publication: 2023-11-08

Can I use this as a soffit for my front porch which is 8x12ft with an attached turret porch extension?

Posée par: Allen
Hi Allen, Yes this would be perfectly feasible with this product, however as another member pointed out it would be best to use vented soffit to ensure ventilation is adequate. Thank you Allen.
Répondue par: Product Expert
Date de publication: 2021-04-14

Is this item designed to fit under the drip edge 

Posée par: Billysw6
Hello Billysw6, thank you for your question. Yes, it should fit under the drip edge.
Répondue par: Product Expert
Date de publication: 2021-06-28
  • y_2024, m_4, d_23, h_5CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.41
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_71
  • loc_fr_CA, sid_1001043541, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 74ms
  • QUESTIONS, PRODUCT