L’événement On se met à l’oeuvre est en cours. N’attendez pas!  Magasinez maintenant

Aperçu

Modèle # FC350B Internet # 1000664078

Idéale pour les menuisiers, les menuisiers et les bricoleurs, la cloueuse à cadre à tête coupée offre une variété de caractéristiques dont une gâchette sélectionnable permettant de choisir entre des modes d'actionnement restrictifs ou par contact. Pour faciliter l'utilisation, l'outil est également équipé d'une fonction de profondeur d'entraînement, d'un mécanisme de verrouillage à clous bas pour vous avertir de la nécessité de recharger l'outil et d'un crochet à chevrons réversible pour suspendre l'outil sur le côté gauche ou droit. De plus, la poignée surmoulée offre confort et contrôle lors du travail.

  1. Léger, il ne pèse que 3,5 kg.
  1. Pouvoir enfoncer des clous jusqu'à 3-1/2 pouces x 0,131 pouce dans du bois d'ingénierie
  1. Echappement réglable sans outil
  1. Accepte les clous à tête ronde et à tête coupée de 30° à 34° sur ruban papier offset de 2 à 3-1/2 pouces
  1. Pression de fonctionnement de 70-120 PSI
  1. Le kit comprend la cloueuse, une fiche mâle de 1/4 de pouce (installée), une clé hexagonale et un manuel d'instructions

Spécifications

Dimensions

Hauteur assemblé (en pouces)
17.5
Hauteur de l’emballage (en pouces)
5.12
Largeur assemblée (en pouces)
5.75
Largeur de l’emballage (en pouces)
12.16
Poids assemblé (en livres)
14
Poids de l’emballage (en livres)
5.96
Profondeur assemblé (en pouces)
19.25
Profondeur de l’emballage (en pouces)
14.06

Détails

Angle de la cloueuse
34
Arrivée d'air minimale recommandée en pi³ standard/min à 90 psi
5-10
Arrivée dair minimale recommandée à 90 psi (en pi³ standard/min)
9.7
Certifié
Pays d'origine
TW-Taiwan
Pression minimale recommandée lors du fonctionnement (en psi)
70
Sans fil/avec fil
Avec fil
Source dalimentation
À air
Système de batteries
Autre
Taille du raccord A (en po)
1/4" M-NTP
Taille maximale de lattache (en po)
3-1/2
Taille minimale de lattache (en po)
2
Tension de batterie
Pas de tension précise

Garanties et certifications

Garantie limitée de 1 an - numéro de téléphone du Service à la clientèle : 1 800 567-7188
Kit de cloueurs à charpente à ruban de papierPORTER-CABLE Kit de cloueurs à charpente à ruban de papierIdéale pour les menuisiers, les menuisiers et les bricoleurs, la cloueuse à cadre à tête coupée offre une variété de caractéristiques dont une gâchette sélectionnable permettant de choisir entre des modes d'actionnement restrictifs ou par contact. Pour faciliter l'utilisation, l'outil est également équipé d'une fonction de profondeur d'entraînement, d'un mécanisme de verrouillage à clous bas pour vous avertir de la nécessité de recharger l'outil et d'un crochet à chevrons réversible pour suspendre l'outil sur le côté gauche ou droit. De plus, la poignée surmoulée offre confort et contrôle lors du travail.
PORTER-CABLE
1000664078
CAD3392024-05-23
Home Depot Canada
Kit de cloueurs à charpente à ruban de papier est évalué 4.6 de 5 de 83.
  • y_2024, m_5, d_20, h_5
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.42
  • cp_1, bvpage1
  • co_hasreviews, tv_8, tr_75
  • loc_fr_CA, sid_1000664078, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 78ms
  • REVIEWS, PRODUCT
Rated 5 de 5 de par Pro grade industry standard quality After a lot of research i bought this item. First i purchased the 21* model FR350B and returned it for the FC350B. FR is for Round head and FC is for Clipped head nails. However the FC350B uses both round or clipped in the paper collated form. This makes your gun compatible with many on the market and out in use in the field today. Helpful when buying and sharing nails with other friends/contractors. After researching the paper collated nails; they are said to be safer as the paper gets desintigrated in the worked product. Whereas the plastic on the 21* FR nails get lodged in the mechanism or ejected. Even with goggles or protective eye wear you don't want to have to think about cast off while working...either for the user or others and you certainly don't want to spend time unjaming your gun. The FC is 30* angle which sets the nail cartridge closer to the handle providing more compact space to fire in close spaces. You'll appreciate it when its needed, but seems second nature while working with it. Both models come with a case, rafter/belt hook, two cushion heads, and adjustable exhaust. Great accessories for the price that many other manufactures lack. Get the industrial fittings for your compressor hook up.
Date de publication: 2013-03-30
Rated 5 de 5 de par Pro Grade Nail Gun @ Killer Price I have a large assortment of Porter Cable air nailers including the FR350A but when I was out shopping on Black Friday, I could not believe that they were practically giving away this gun for a buck-29. I couldn't get this thing in the basket quick enough and I've been using it every day since. To compare the two guns, the FR350A is a workhorse but this gun can run circles around it on every level. The FR is a round head only using plastic collated 22 deg nails and weighs ~15 pounds. The FC will take both round or clipped head paper collated in the 30-34 deg range, weighs ~7.5 pounds and has has been redesigned to drive 3.5" nails in engineered lumber. The gun comes equiped with Tool-lessTrigger Selection, Tool-less Depth Adjustment, Framers Hook, Low-Nail Lockout, Case, Oil, Allen Wrench, & Manual. As of today, you can still get this gun at this incredible price but you will have to do some looking as most stores sold out quickly.
Date de publication: 2013-12-08
Rated 5 de 5 de par Good purchase I bought this nailer for basement finishing work. the nailer is solid and works very well with my 3 gallon compressor. The only this is the size of the rear end. When I set up the frames on the floor it doesn't allow me to be totally parallel to the basement floor because the rear of the nailer is fat. I like to keep my tools perfectly clean with no scratches so I placed some tape where the nailer would scrap against the basement floor while framing the walls on the floor. Very good purchase and I would do it again.
Date de publication: 2015-01-27
Rated 4 de 5 de par Great value for the price. Bought it for a future project (Garage). Have only used it once to build a large crate for work. Pros: Had no issues driving 3 1/4" through 2x10s and into 4x4s. Knots were no problem either. Had plenty of power. Comes with removable soft tip for finesse jobs. Cons: Overall gun is bulky and a bit top heavy. Cannot imagine using this all day every day. Also "feature" stops you with 5 nails left to let you know the gun is "empty". Doesn't seem like a big deal until you need two more nails to finish the job but you have to stop and load another strip. Overall I would recommend this to any DIYer like I am.
Date de publication: 2011-12-24
Rated 5 de 5 de par Great nail gun for the DIY homeowner Having owned this Porter Cable nailer now for just over 1.5yrs, can say without a doubt I made the right decision in my purchase. Looked at many guns in this category, different vendors, 21° vs. 34°, plastic strip collated vs. paper tape nails, etc. This light-weight gun never misfires, this gun uses paper-tape collated nails & those are less expensive then the plastic collated nails the 21° nail guns use, so no plastic debris from discharging nails flying all over the place & needing to be cleaned up. This FC350B shoots both clipped-head & full-head paper-tape collated nails, a great bonus. Haven't shot anything larger then 3-1/4" nails, but it sank all the way into the wood material with ease, make sure you add a drop or two of air tool oil when using it. I added this gun to my Porter Cable collection of pneumatic guns, only missing the 15-gauge DA gun. By far thoroughly satisfied with PC guns, ease of use, ease of cleaning as the firing areas are easily accessible to clean. The nail guns & staplers take multiple varieties of nail manufacturers, Paslode being my nail of choice if HD is out of Porter Cable nails/brads/staples. You won't go wrong with the purchase of this nailer, or any Porter Cable nailer. The gun also comes with a nice heavy-duty plastic molded carry case & small bottle of air tool oil, descriptive owners manual & an extra bump stop for the gun.
Date de publication: 2015-04-27
Rated 5 de 5 de par Had to Buy Borrowed one from a friend. Ease of use made me want one. Saw it on sale for $129.00 and had to get one. SCORE!!! Depth adjustment easy to use.
Date de publication: 2013-12-08
Rated 5 de 5 de par Great Nailer Works Great. Ready to throw away my hammers now. Easy to use and very powerful. Split my board the first test, but quickly adjusted it to the correct driving depth. Accepted full head and clipped nails. Have driven over 300 nails without a misfire or problem. Was able to build a new staircase to the basement in one day. A little heavy by the end of the day, but still easier than swinging the hammer.
Date de publication: 2015-06-30
Rated 4 de 5 de par Good for price but LOUD I am a carpenter for a large remodeler and frame probably 30% of year. This gun has been great to me. It does the job and doesn't jam. It has plenty of power as well; I've never had trouble sinking nails and the depth adjustment is straightforward and tooless. Some minor issues I've had with it: The lock is very close to the trigger so people who borrow the gun often lock it accidentally. This gun is LOUD. Plan to wear headphones if you want to keep your hearing.
Date de publication: 2016-01-14
  • y_2024, m_5, d_20, h_5
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.42
  • cp_1, bvpage1
  • co_hasreviews, tv_8, tr_75
  • loc_fr_CA, sid_1000664078, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 48ms
  • REVIEWS, PRODUCT

does it only shoot clipped head nails

Posée par: ww
The Grip Rite nails sold at Home Depot are full head nails. However, they have an offset that allows the clipped head nailer to shoot full head nails. I used a couple of thousand nails with no problems.
Répondue par: Jr
Date de publication: 2023-05-04

can you nail wood to Concrete or cement with this gun

Posée par: MiMi
No. It can damage the plunger. It may fasten but not good for the gun.
Répondue par: bugs
Date de publication: 2023-05-05

will this gun shoot a framing pasload nail ?

I have boxes of pasload nails and need to use them up. I tried them with a used porter cable but the slot was too narrow or slot was damaged.they would not load into gun..
Posée par: crusty
Yes, I have nothing but Paslode paper-collated nails, both Brite & Hot-dipped, shoots them perfectly. Paslode is less expensive then many of the other brands out there, too
Répondue par: BuffaloBlue
Date de publication: 2023-05-03

What is the proper way to lubricate this nailer?

Most require oil to operate. Does the framing nail require oil and how much and where?
Posée par: Dave
I just squirt a few drops where the air hose attaches. I add a couple of drops of oil every time I insert a new rack of nails.
Répondue par: Caveman
Date de publication: 2018-03-01

I bought one of these today and immediately put it to work.  When I hold the trigger in automatic mode and press the head to wood, it fires two nails very rapidly before I can lift it up.  What am I doing wrong?

Posée par: Steve
Hello Steve Thank you for your contact. We apologize for any trouble or inconvenience in finding information. Please contact PORTER-CABLE directly so that we may work together to resolve this issue. Best Regards Sherri C PORTER-CABLE
Répondue par: PorterCableProductExpert
Date de publication: 2021-07-12

Does this fit between 16" centers?

Posée par: Wayne
The FC350B is Unit height 14 inches, Unit Length 14.25 inches and Unit Width 3.5 inches. it will fit between 16" centers.
Répondue par: StanleyBlackDeckertProductExpert
Date de publication: 2023-04-03

will this gun shoot round head paslode nails

Posée par: pete
Yes I have 3 boxes of Paslode galvanized round-head nails of different sizes that I've used over the past 4-5 years without any issues.
Répondue par: BuffaloBlue
Date de publication: 2019-09-26

My porter cable is 34 degrees. Seems Home Depot does not carry 34 degree nails.

Posée par: bing
Thank you for your recent inquiry with The Home Depot, Bing. Please click the following link for 34 deg nails: http://www.homedepot.com/s/34%2Bdeg%2Bnails?NCNI-5 We appreciate your business and look forward to serving you in the future. Thank you for shopping Home Depot.
Répondue par: THDSupport
Date de publication: 2021-09-24
  • y_2024, m_5, d_21, h_6CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.42
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_23
  • loc_fr_CA, sid_1000664078, prod, sort_[SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_homedepot-canada
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 75ms
  • QUESTIONS, PRODUCT