Home>Know-How Centre>Outdoors>Making Stringers

Projects

Making Stringers

Project Overview

Making Stringers

There are two types of stringers:Open stringers, also called cut stringers, have notches for steps cut into them. The treads are attached to the notches. Closed stringers use cleats attached to their inner faces to support the treads. Open stringers take a little more time than closed ones. Plan to build deck stairs at least 3 feet wide for ease of traffic flow and safe use. Use the best 2x12 boards you can find for stringers. Open stringers should be cut from pressure-treated lumber. Remember to apply preservative to the cut edges.

7 Steps

  1. SET STAIR MEASUREMENTS ON SQUARE
  2. MARK THE TOP CUTTING LINE
  3. MARK THE CUTTING LINE
  4. FINISH CUT WITH A JIGSAW
  5. TRACE AN OPEN STRINGER
  1. ATTACH STAIR ANGLES
  2. ATTACH STAIRS FROM UNDERSIDE
Show all steps »
SET STAIR MEASUREMENTS ON SQUARE
SET STAIR MEASUREMENTS ON SQUARE

Step 1

SET STAIR MEASUREMENTS ON SQUARE

Lay the framing square on the stringer board so the unit run measurement on the outside of the wide body of the square intersections the edge of the board. Clamp a stair gauge on the inside edge of the leg so it won’t interfere with the marking. Set the length of the unit rise on the outer edge of the narrow leg so it intersects the edge of the board. Clamp on a stair gauge to hold the measurement. Mark the rise and the run for the first step at the top end of the stringer. Place the framing square on the board for the stringer with the gauges resting against what will be the top edge. Intersect the corner of the board with the rise line. The rise measurement at the top end of the stringer sets the stringer at the correct distance from the decking surface.

MARK THE TOP CUTTING LINE
MARK THE TOP CUTTING LINE

Step 2

MARK THE TOP CUTTING LINE

Extend the rise line to the bottom edge of the stringer. Mark an ‘X’ in waste areas to prevent confusion when you start cutting. Mark the rise and run for the next step. Slide the framing square down the stringer edge until the rise line touches the point where the tread line from the previous step intersects the board edge. Make certain the stair gauges rest against the board. Repeat this process to mark all steps. Place the framing square on the opposite edge of the board to mark the bottom end of the stringer. The stair gauges must rest against the board edge to maintain proper alignment. First extend the final rise line across the end of the board. Then mark a line the distance of the rise from the tread line on the last step.

MARK THE CUTTING LINE
MARK THE CUTTING LINE

Step 3

MARK THE CUTTING LINE

Mark another line below the last line, at a distance equal to the thickness of the tread. This is the bottom of the stringer. Subtracting the tread thickness from the first riser will leave the first step up from the ground at a comfortable height. Start cutting the stringer at the top end of the extended rise line. Then make the top tread cut. Use a sharp blade in a circular sq to make crisp cuts with clean edges. When making the cuts, stop the saw blade just before it reaches the corner.

FINISH CUT WITH A JIGSAW
FINISH CUT WITH A JIGSAW

Step 4

FINISH CUT WITH A JIGSAW

Complete the cuts in the corner with a jigsaw, cutting along the outside of the krf to remove all the waste. Use the completed stringer as a template to mark boards for the remaining stringers. First hold the completed stringer in place to check for accuracy. Then clamp the template stringer to each board to keep the marking accurate.

TRACE AN OPEN STRINGER
TRACE AN OPEN STRINGER

Step 5

TRACE AN OPEN STRINGER

If your closed stringers will be used in conjunction with open stringers, cut an open stringer first and use it as a template to mark the closed stringers. Position the template with the step corners set back from the edge of a closed stringer board by the thickness of the tread. Mark the tread positions on the closed stringer. Although you can mark the rise lines also, they’re unnecessary. You need only the tread lines for mounting the stair angles. Cut the extended riser line at the tip end of the stringer. Then cut the bottom of the stringer to conform to the method you’ll use to attach stringers to the landing pad.

ATTACH STAIR ANGLES
ATTACH STAIR ANGLES

Step 6

ATTACH STAIR ANGLES

Install the stringers in their proper locations and fasten a stair angle at each tread location on the closed stringers. You could use 2x2 cleats instead. Attach a stair angle at each tread on the open stringers. Using a stair angles on the open stringer provides an invisible connection. Install the stair angles on opposite side of the stringer, every other tread.

ATTACH STAIRS FROM UNDERSIDE
ATTACH STAIRS FROM UNDERSIDE

Step 7

ATTACH STAIRS FROM UNDERSIDE

Drive fasteners recommended by the manufacturer (usually short lag screws) through the stair angles into the undersides of the treads. Use a ratchet and an appropriate-size socket to drive fasteners in spaces too small to use the drill.

Write a Review
QUICK RATE:

You have rated

 out of 5 stars.

Do you want to submit this quick rating?

Yes No

Thank you!
Your quick rate has been submitted.

Please note it may take up to 8 hours for your quick rating to appear.

Sorry we are currently experiencing technical difficulties. Please try and resubmit your Quick Rating.

Thank you, you have already quick rated this product.  out of 5

Project Details

Skill Level: Beginner

Time: 2 hours

Before you start, read this »

Due to differing conditions, tools, and individual skills, The Home Depot® assumes no responsibility for any damages, injuries suffered, or losses incurred as a result of attempting to replicate any of the home improvement ideas portrayed in this website Before beginning any home improvement project, review it thoroughly to ensure you or your contractor can finish the project and if any doubts or questions remain, consult local experts or authorities. Because codes and regulations vary greatly, you always should check with authorities to ensure that your project complies with all applicable local codes and regulations. Always read and observe all of the safety precautions provided by any tool or equipment manufacturer, and follow all accepted safety procedures.

Materials

  • Lumber
  • fasteners
  • preservative

Tools

  • Tape measure
  • framing square
  • stair guages
  • circular saw
  • jigsaw, drill
  • ratchet and socket
  • random orbital sander

Related Resources

Projects